Go-Back-N ARQ

Go-Back-N ARQ is a specific instance of the automatic repeat request (ARQ) protocol, in which the sending process continues to send a number of frames specified by a window size even without receiving an acknowledgement (ACK) packet from the receiver. It is a special case of the general sliding window protocol with the transmit window size of N and receive window size of 1. It can transmit N frames to the peer before requiring an ACK.

The receiver process keeps track of the sequence number of the next frame it expects to receive. It will discard any frame that does not have the exact sequence number it expects (either a duplicate frame it already acknowledged, or an out-of-order frame it expects to receive later) and will send an ACK for the last correct in-order frame.^[1] Once the sender has sent all of the frames in its window, it will detect that all of the frames since the first lost frame are outstanding, and will go back to the sequence number of the last ACK it received from the receiver process and fill its window starting with that frame and continue the process over again.

Go-Back-N ARQ is a more efficient use of a connection than Stop-and-wait ARQ, since unlike waiting for an acknowledgement for each packet, the connection is still being utilized as packets are being sent. In other words, during the time that would otherwise be spent waiting, more packets are being sent. However, this method also results in sending frames multiple times – if any frame was lost or damaged, or the ACK acknowledging them was lost or damaged, then that frame and all following frames in the send window (even if they were received without error) will be re-sent. To avoid this, Selective Repeat ARQ can be used.^[2]

Pseudocode

These examples assume an infinite number of sequence and request numbers.^[1]

N  := window size
Rn := request number
Sn := sequence number
Sb := sequence base
Sm := sequence max


function receiver is
    Rn := 0
    Do the following forever:
        if the packet received = Rn and the packet is error free then
            Accept the packet and send it to a higher layer
            Rn := Rn + 1
        else
            Refuse packet
        Send a Request for Rn


function sender is
    Sb := 0
    Sm := N + 1
    Repeat the following steps forever:
        if you receive a request number where Rn > Sb then
            Sm := (Sm − Sb) + Rn
            Sb := Rn
        if no packet is in transmission then
            Transmit a packet where Sb ≤ Sn ≤ Sm.  
            Packets are transmitted in order.

Choosing a window size (N)

There are a few things to keep in mind when choosing a value for N:

The sender must not transmit too fast. N should be bounded by the receiver’s ability to process packets.
N must be smaller than the number of sequence numbers (if they are numbered from zero to N) ^{[clarification needed]} to verify transmission in cases of any packet (any data or ACK packet) being dropped.^[2]
Given the bounds presented in (1) and (2), choose N to be the largest number possible.^[3]^{[failed verification]}

References

^ ^a ^b Kurose, James F.; Keith W. Ross. Computer Networking: A Top-Down Approach. ISBN 0-321-49770-8.
^ ^a ^b Tanenbaum, Andrew S. (2003). Computer Networks (4th ed.). Prentice Hall. ISBN 0-13-066102-3.
^ Marbach, Peter. "ARQ Protocols" (PDF). Retrieved August 24, 2013.

External links

Go-Back-N ARQ demonstration in a Java applet

[KuroseRoss-1] Kurose, James F.; Keith W. Ross. Computer Networking: A Top-Down Approach. ISBN 0-321-49770-8.

[Tanenbaum-2] Tanenbaum, Andrew S. (2003). Computer Networks (4th ed.). Prentice Hall. ISBN 0-13-066102-3.

[3] Marbach, Peter. "ARQ Protocols" (PDF). Retrieved August 24, 2013.

[1]

[2]

[3]

Pseudocode

Choosing a window size (N)

References

See also

External links